Skip to main content
Guides

How Failsafe Hydraulic Brakes Work

By 27 October 2026No Comments8 min read

A failsafe hydraulic brake is held on by springs and released by hydraulic pressure. Pressure at the brake port pushes the springs back and frees the shaft. Vent the release pressure and the springs clamp the brake again. Holding depends on correct installation, brake condition and a load within the rated static capacity. That is how failsafe hydraulic brakes work.

Winches, deck cranes, conveyors and tunnelling machines all need to hold a load when the machine stops or loses pressure. This guide explains the failsafe principle, what happens inside a multi-plate brake, what release pressure means for your circuit, and how to choose the right Staffa brake for a Staffa radial piston motor.

What failsafe means for a hydraulic brake

Hydraulic brakes commonly use one of two operating arrangements. In one, pressure applies the brake and springs release it. In the other, springs apply the brake and pressure releases it. The spring-applied arrangement is commonly called failsafe because it does not need hydraulic pressure to remain applied.

A spring applied, hydraulically released brake applies when its release pressure is vented. A pump trip, burst hose, power cut or emergency stop does not by itself prove that the brake port has depressurised: trapped pressure, valves and sequencing all matter. The system must stop and secure the load safely, then keep the holding torque within the brake rating.

That is why a failsafe brake is the usual choice wherever a load could run back or drop: winch drums, crane slews, inclined conveyors and anything holding a suspended load.

How failsafe hydraulic brakes work inside a multi-plate brake

Staffa brakes use a multi-plate design. Multiple friction surfaces provide high holding torque in a compact assembly. The plates run in oil. The following sections explain the main components and how they work together.

The plate pack

A stack of thin plates sits between the shaft and the housing. Alternate plates are keyed to the rotating shaft and to the fixed housing. Squeeze the stack together and friction between the plates locks the shaft to the housing.

The springs

Springs bear on the plate pack through a piston. With no pressure at the brake, they clamp the plates together and the brake holds at its rated static torque.

The release piston

When oil under pressure reaches the brake port, it pushes a piston against the springs. The springs compress, the clamping force comes off the plates, and the shaft turns freely.

Re-applying the brake

When the brake port is vented, the oil behind the piston returns to tank and the springs push the piston back. The plates are clamped again and the load is held.

  1. No pressure at the brake port: springs clamp the plates, the brake holds.
  2. Release pressure applied: the piston compresses the springs, the shaft is free.
  3. Release pressure safely vented: the springs re-apply the brake.
Staffa multi-plate brake, detail view
A Staffa multi-plate brake, made by Advanced Components to mount directly to Staffa motors.

Release pressure and the release circuit

Every brake has a minimum pressure for full release. On Staffa brakes it is 28 to 40 bar, depending on size, and the brake takes up to 70 bar continuous. Two things follow for the circuit.

  • Enough pressure. Below the full release pressure the plates may not separate fully, and a brake that drags runs hot and wears.
  • Not too much. Keep the pressure at the brake port within 70 bar continuous. Where the supply runs higher, a pressure reducing valve is the usual answer.

The brake also needs a volume of oil to release, from 65 cc on the F032 to 260 cc on the F402. The supply has to deliver that volume quickly enough for the brake to release fully before the motor shaft starts to rotate.

In most drives the release pressure comes from the motor circuit, so the brake releases when the motor is asked to turn and re-applies when the circuit is vented. The circuit must keep the load controlled while the brake releases, achieve full release before the motor shaft rotates, and stop the load before re-applying the parking brake. Our motor-mounted valves give motor control with brake release, and the brake ports are ¼ inch BSP on the F032 and F102 and ½ inch BSP on the F202 and F402.

Holding a load, not stopping it

Staffa brakes are parking brakes. They are rated on static brake torque, the torque they hold with the brake applied. In a typical hydraulic drive, the motor and its circuit bring the load to rest and the brake then holds it.

If your machine needs the brake to stop a moving load, for example as part of an emergency stop, talk to us before you choose a size. We will look at the duty with you.

Choosing a Staffa brake for your motor

We are the original equipment manufacturer of Staffa brakes, and the only source of them: made by us, only from us. There are four sizes, each made to mount directly to its Staffa motor frames.

BrakeStatic brake torque (Nm)Full release pressure, min. (bar)Continuous pressure, max. (bar)Oil for full release (cc)Staffa frames
F0322,750317065HMB030, HMB045; HMC030, HMC045
F1026,2004070117HMB060, HMB080, HMB100; HMC080
F20213,8302870230HMB125, HMB150, HMB200; HMC125, HMC200
F40232,5402870260HMB270, HMB325, HMB400, HMB500; HMC270, HMC325, HMC400

Start with the full motor model code, shaft and mounting, then check that the brake has the holding torque needed for the duty. The table lists the motor frames in the published data sheet; HMB400 denotes the HMHDB400 frame. Confirm the complete motor and brake combination against the installation drawing. All four sizes work from −40 to +80 °C, and output shafts can be splined to BS 3550 or DIN 5480, or keyed. The Staffa motors pages give the frame sizes, and the Staffa brakes page has the full data and downloads.

Older brakes

The multi-plate range replaces the older F100 and F200 shoe brakes. It is more compact, has fewer moving parts and is easier to maintain. We still supply the older F100 and F200 brakes for existing machines, or can help you move to the multi-plate design.

More torque: a Combination Drive

When one motor and brake are not enough, the brake can be built into a planetary gearbox. A Combination Drive puts a Staffa motor, a Staffa brake and the gearbox in one package.

Find the right brake for your motor

Send us the model code from the motor nameplate (our guide on how to read a Staffa motor model code shows what it tells us), the holding torque you need and the output shaft, and we will confirm the brake. Email us your details or call +44 (0)1535 655151. We also service and repair Staffa brakes and supply original spares; see spares and repairs.

Frequently asked questions

What does spring applied, hydraulically released mean?

Springs apply the brake and hydraulic pressure releases it. When release pressure is vented, the brake can hold a stopped load within its rated static capacity. The complete circuit must provide safe release, stopping and re-application.

What happens if the hydraulic supply fails?

The brake applies if the release pressure falls sufficiently. The circuit must reliably vent that pressure and control a moving load; trapped pressure can delay application. Confirm the fault response and holding capacity for the complete machine.

What pressure releases a Staffa brake?

Full release needs 31 bar on the F032, 40 bar on the F102 and 28 bar on the F202 and F402. Every size takes up to 70 bar continuous at the brake port.

Can a Staffa brake stop a moving load?

Staffa brakes are parking brakes, rated on the static torque they hold. In most drives the hydraulic circuit stops the load and the brake then holds it. If your duty needs the brake to stop a moving load, ask us before you choose a size.

Which Staffa brake fits my motor?

Each brake size has its own listed motor compatibility, as shown in the table above. The full motor code, shaft and mounting must be checked against the installation drawing, together with the required holding torque.

Sources: Staffa multi-plate brakes technical data sheet AC-DS-STB-01, Issue 1, October 2026 (Advanced Components), drawing on the Staffa brakes multi-plate technical brochure R1 (August 2023) and the Kawasaki Precision Machinery (UK) Staffa brakes flyer MYK6464 (November 2023).