Home › Products › Staffa motors › HMC
Staffa HMC Dual Displacement Motor
Two displacements, changed on the run.
Home › Products › Staffa motors › HMC
Two displacements, changed on the run.
Seven frames from 492 to 5,326 cc/rev, with a freewheel in zero displacement. Genuine Kawasaki Staffa motors and spares, supplied and supported from Silsden, West Yorkshire.

5,326cc/rev
Largest displacementHMC325; the HMC030 reaches 492 cc/rev.
2speeds
DisplacementsAny two codes per frame, changed on the run.
1,500rpm
Freewheel speedIn zero displacement, with crankcase flushing.
213kW
Intermittent powerHMC270 and HMC325; 189 kW continuous.
Overview
The Staffa HMC is Kawasaki’s dual displacement radial piston motor. It runs at two preset displacements and switches between them while turning, so one motor can give high torque at low speed and less torque at higher speed.
Seven frames run from HMC030 to HMC325, with maximum displacements from 492 to 5,326 cc/rev. A directional control valve, on the motor or mounted remotely, selects the displacement hydraulically, and if control pressure is lost the motor returns to its high displacement. Zero displacement lets it freewheel at up to 1,500 rpm, and a constant pressure regulator option makes the displacement continuously variable.
We are a UK distributor for Kawasaki Precision Machinery, supplying HMC motors and genuine KPM spares, and we make the Staffa brakes that fit them.
Which Staffa motor?
Key advantages
Switch between two preset displacements while the motor is turning.
Zero displacement for freewheeling at up to 1,500 rpm; KPM prefers the HMC to fixed displacement motors for this.
If control pressure is lost, the motor shifts to its high displacement.
A constant pressure regulator adjusts displacement to hold inlet pressure, set from 180 to 220 bar.
High efficiency and good breakout torque, with smooth running at low speed.
Marine paint and cylinder heads, improved shaft seal life, thermal shock resistance. ATEX enquiries are subject to confirmation of the current motor specification and documentation by Kawasaki Precision Machinery.
Technical data
Each frame offers displacement codes from its maximum down to zero, and the motor runs on any two, set in the model code. Figures are at the maximum displacement. Where two speeds are shown, the first is with size 3 valve housings and the second with size 4.
| Frame code | Max. displacement (cc/rev) | Running torque (Nm/bar) | Continuous pressure (bar) | Continuous speed (rpm) | Continuous power (kW) | Intermittent power (kW) |
|---|---|---|---|---|---|---|
| HMC030 | 492 | 6.86 | 207 | 450 | 60 | 66 |
| HMC045 | 737 | 10.63 | 250 | 450 | 99 | 119 |
| HMC080 | 1,600 | 23.9 | 250 | 270 / 365 | 138 | 170 |
| HMC125 | 2,048 | 29.9 | 250 | 215 / 300 | 135 | 152 |
| HMC200Also HMHDC200 | 3,087 | 46.6 | 250 | 175 / 230 | 174 | 195 |
| HMC270 | 4,588 | 69.4 | 250 | 150 | 189 | 213 |
| HMC325 | 5,326 | 80.4 | 250 | 130 | 189 | 213 |
Intermittent pressure is 300 bar (250 bar on the HMC030) for 15% of the duty in periods of up to 5 minutes. Every frame freewheels at up to 1,500 rpm in zero displacement, with 15 l/min of crankcase flushing above 1,000 rpm. Source: KPM UK HMC datasheet (file M-200203.17-HMC), which lists every displacement code with its torque, speed and power.
Applications
Deck and mooring winches, deck cranes, ROV launch systems, pipe handling
Shredders and waste treatment plant
Crushers and conveyors
Injection moulding screw drives, die casting machines
Tunnel boring machines
Need more power from two speeds? The HPC is the high power version of the HMC.
Can’t find it?
Send us the model code from the nameplate and we will find the right drawing, CAD model or spares list.
Replacing a motor
Every HMC carries its model code on the nameplate. Send us the full code and we will match the frame, both displacements, the control and the options, or tell you what has replaced them.
An HMC model code carries two displacement codes, such as 250/100, and a control code such as CS. Send us the whole code so we match all of them.
The full model code, a photo of the nameplate, photos of the shaft and port face, and what the motor drives.
We supply genuine KPM spares for HMC motors. Quote the model code, or the part number from the spares drawing. Need a repair rather than a replacement? Call us and we will talk it through.
Model code
Let’s find your motor
We just need three details.
Replacing one? Send us the model code from the nameplate and a photo, and we will work from those.
1
Continuous and peak, at the motor shaft.
2
Shaft rpm, and the range if it varies.
3
Hours per day, starts per hour and direction changes.
Prefer us to call you? Request a callback.
FAQs
Anything else? Call +44 (0)1535 655151 or email sales@advanced-components.com.
Yes. A directional control valve selects the displacement hydraulically while the motor turns. Control pressure must be at least 67% of the higher port pressure, and at least 3.5 bar.
The motor shifts to its highest displacement, so it keeps its full torque.
Yes. With zero displacement selected, the ports connected and the circuit boosted, it freewheels at up to 1,500 rpm. Between 1,000 and 1,500 rpm it needs up to 15 l/min of crankcase flushing.
Both are dual displacement. The HPC is the high power version, rated up to 278 kW continuous with crankcase flushing, against 189 kW for the HMC.
Mineral oil as standard. Phosphate ester (HFD) runs with the F3 prefix at the full 250 bar continuous. Water-based fluids (HFA, HFB and HFC) run with the F11 prefix at 103 to 138 bar continuous depending on type, and HFA and HFC at half the mineral oil speed limits.