A Staffa motor model code is on the motor’s nameplate. Read left to right, it gives the fluid the motor is built for, the series and frame size, the shaft, any displacement settings, the ports, the speed sensor, the design series and any special features. The full code lets us check the original specification and confirm a suitable replacement or the correct spares.
Every Staffa radial piston motor carries its model code on the nameplate. That code is the quickest route to a like-for-like Staffa motor replacement, the right seals or the right spares drawing, because it records how that particular motor was built, not just its size.
This guide explains each part of the code across the Staffa motor range, from the fixed displacement HMB to the four-speed HPC400, and what to send us when you need a motor or parts.
Where to find the model code
The code is on the Staffa motor nameplate, fixed to the motor body. Clean the plate before you photograph it, and take the picture square on so every character can be read.
On a geared unit, the gearbox carries its own nameplate code, so photograph that plate as well. If a brake is fitted, note the brake model too. Together they tell us the gearbox, the motor and the brake.
If the plate is missing or worn, do not give up. Photos of the motor, the shaft and the port face, with any numbers stamped or cast on the body, will still help us identify it.
The Staffa motor model code, field by field
Most Staffa codes follow the same pattern, with extra fields where a series needs them. Using the Staffa HMB as the example, the code sets out these fields from left to right.
| Field | Example | What it tells us |
|---|---|---|
| Fluid | Blank, F3 or F11 | Blank for mineral oil, F3 for phosphate ester (HFD), F11 for water-based fluids (HFA, HFB and HFC). |
| Model | HMB or HMHDB | The series. HMHDB is the heavy duty version. |
| Frame size | 030 to 500 | The frame designation, not a direct displacement in cc/rev. The HMB range spans 188 to 8,000 cc/rev; some frames have more than one displacement. |
| Shaft type | S3 or P1 | The shaft end, coded P, Q, S, T or Z, with numbered variants on the larger frames. |
| Shaft orientation | Blank or V | Horizontal or down as standard; V for a shaft pointing vertically up. |
| Main ports | SFM3 | The valve housing: SFM for SAE flange ports, SM for a bolt-on manifold. |
| Speed sensor | Blank, Tj or Ts | Tj is a Hall effect sensor giving speed and direction; Ts adds a module with a tacho, a relay and a 4 to 20 mA output. |
| Design series | Series number | The version of the design your motor was built to. |
| Special features | P or PL code | P for catalogued options; PL for features KPM numbers individually. |
Some fields decide whether a motor bolts straight into your machine: the shaft, the orientation and the ports. Others decide what is inside it. The fluid prefix matters for the seals, and the special features cover options such as a high pressure shaft seal or marine paint.

Codes for dual and multi-displacement motors
Fixed displacement motors, the HMB and HPB, run at one displacement. Motors that change displacement add a displacement code for each setting, and most add a control code too.
| Series | Type | Frames | Displacement codes in the model code |
|---|---|---|---|
| HMB, HMHDB | Fixed displacement | 030 to 500 | None |
| HPB, HPHDB | Fixed displacement, high power | 060 to 325 | None |
| HMC | Dual displacement | 030 to 325 | Two, such as 250/100, plus a control code: X, C, CS, CP or CHP |
| HPC | Dual displacement, high power | 080 to 325 | Two, such as 250/100, plus a control code: X, C, CS or C1 |
| HMF, HMHDF | Three displacements | 100 to 325 | Three, high, medium and low, such as 280/140/00 |
| HPC400 | Four speeds from two piston banks | One frame | Four, high and low for each bank, such as 200/05/200/05 |
| Smart Motor (HPCe, HPCi) | Infinitely variable | 200 and 325 | High and low, in cubic inches, in steps of 5 |
The HMC, HPC and HMF datasheets list every displacement code with its torque, speed and power, so the numbers in the code tell us how the motor performs at each setting. On the HPC400 the settings are named in cubic inches: setting 400 is both banks at high displacement, 6,555 cc/rev.
Send every displacement code, in order. Two HMC motors on the same frame with different codes are set up for different duties, and a replacement needs to match both settings and the control.
Why the full code matters for a Staffa motor replacement
The frame size alone is rarely enough. Two motors on the same frame can differ in shaft, ports, sensor, seals and fluid. Even the displacement can vary: the HMB030 comes in 188, 442 and 492 cc/rev versions.
Superseded parts
Staffa motors stay in service for a long time, so older codes often point to parts that have since been replaced. The HMB010, for example, is replaced by the 188 cc/rev HMB030. KPM’s December 2024 HMB datasheet also replaces the F3, FM3, F4 and FM4 valve housings with SM and SFM housings. With the full code, we can tell you what has replaced your motor or housing and confirm the match.
Older motor codes
On Staffa G-range geared units, the motor is named B for fixed displacement or C for dual displacement, followed by the frame, such as B200 or C080. The later unit code combines the gearbox and motor, so GB3200 is a G030 gearbox with a B200 motor. Our Staffa gearboxes page lists the geared units by their original and later codes.
Finding the spares list from the code
KPM publishes spares drawings by frame, which is how people usually look for a Staffa motor parts list. For the HMB:
- 016472: HMB030
- 016502: HMB030 and HMB045, two-part
- 016451: HMB060 to HMB200
- 016396: HMB270 and HMB325
- 016506: HMHDB400
The HPC400 has its own drawing, 016709. HMC and HPC spares drawings cover the applicable 5-cylinder and 7-cylinder frames; use the drawing for the exact series, frame and design version. The frame points to the drawing; the shaft, port, seal and fluid options in the code narrow down the parts.
Quote the model code, or the part number from the drawing, and we will supply genuine KPM spares. If a brake is fitted, note its model as well: F032, F102, F202 or F402, or F100 or F200 on older machines. We are the original equipment manufacturer of Staffa brakes, so brake spares come from us. For servicing or a repair, see spares and repairs.
Send us your model code
We are a UK distributor for Kawasaki Precision Machinery, supplying Staffa motors and genuine KPM spares. Send us the full model code, a photo of the nameplate, photos of the shaft and port face, and what the motor drives. We will match a replacement, find the spares or arrange a repair. Email us your model code, or call +44 (0)1535 655151.
Frequently asked questions
Where is the model code on a Staffa motor?
On the nameplate fixed to the motor body. Photograph it square on, and photograph any gearbox nameplate too, and note the brake model if one is fitted. If the plate is missing or unreadable, send photos of the motor, shaft and port face, with any numbers stamped or cast on the body.
Do I need the whole code, or just the frame size?
The whole code. Motors on the same frame can have different shafts, ports, sensors, seals and displacement settings, and some parts have been superseded. The full code lets us check the original specification, any superseded parts and the suitability of a replacement.
What does F3 or F11 at the start of the code mean?
It shows the fluid the motor is built for. No prefix means mineral oil, F3 means phosphate ester (HFD), and F11 means water-based fluids (HFA, HFB and HFC).
What replaced the HMB010?
The HMB030 at 188 cc/rev, rated 207 bar continuous and 500 rpm. Send us the code from your HMB010 nameplate and we will confirm the match.
Can you find the spares list from the model code?
Yes. The frame tells us which KPM spares drawing applies, such as 016451 for the HMB060 to HMB200, and the rest of the code narrows down the parts. Send us the code and we will supply genuine KPM spares.
Sources: KPM UK Staffa datasheets: HMB, M200112.24-HMB (revised December 2024); HPB, file M-200601.18-HPB; HMC, file M-200203.17-HMC; HPC, file M-200303.17-HPC; HMF, file M-200512.17-HMF; HPC400, Cat. No. M-2004/03.26; Smart and Smart+, file M-200712.24-HPCe. Staffa multi-plate brakes data sheet AC-DS-STB-01 (October 2026). Staffa G-range Technical Bulletins T107, T112 and T113 (December 1980) and T114 (April 1981).